 |
Email #10 |
| |
Limited Quantity Parts - Special Savings!
Wouldn't it be nice if Ford sold all their prototype models at deep discounts? Welder Series thinks it would be great; that's why we're offering great deals on some of our prototypes. Some of these parts may be items that we designed for builders who have changed how they perform a certain job... others may have just been tweaked and replaced. Whatever the reason, they are still high quality pieces that may be just what you're looking for. If you don't see something you need, give us a call and we'll talk about it. I've included the quantity of each item. When they're gone, they may not be restocked. |
 |
AIRSPRING UPPER PLATE - Will fit Firestone's F6957 double convoluted air spring. 1/4" steel. #474201C. $10/ea, 3 left. |
 |
BRAKE BOOSTER PLATE - Will mount 7" or 8" street rod boosters with 3-3/8" x 3-3/8" mounting stud spacing. Center hole is 4-3/4" from boxing plate edge. Formed for extra strength. #004053. $13/ea, 7 left. |
|
CLUTCH PEDAL ARM - Straight up through the floor. 5.75:1 ratio. Pedal arm is welded to the left of the pivot tube. To be used with #20267 bushings, sold seperately. #10108. $25/ea, 5 left. |
|
MASTER CYLINDER MOUNT/ PEDAL KIT - Great for T's and Model A's when a straight pedal works best. Complete as pictured. #10100. #70/ea, 3 left. |
 |
PEDAL PIVOT PIN - Pedal mounting section is 5/8" diameter x 1-3/8" long. Large section is 1" diameter x 2-3/8" long. #20271. $6.50/ea, 43 left. |
|
RACK MOUNT - 5/8" x 1-1/8" slotted hole. Hole center is 1-3/8" ahead of the crossmember face. Usually only used on the passenger side. #213126. $9.50/ea, 5 left. |
 |
RAD MOUNT - Designed for 33-34 Fords with a Mustang II crossmember, but can be used to mount almost anything. #00107D 00107P. $5/ea, 4 Dr., 5 Pass. |
 |
SHACKLE BUSHING - 3/4" OD x 1/2" ID with a 1" shoulder. Black urethane. Made for 1-3/4" springs. These are half bushings - 2 required for each spring eye and 2 for each perch. #MJ1298. $1.00/ea, 806 left. |
 |
SHOCK MOUNTING CONE - 3-3/8" diameter, 1-1/4" high, 7/8" hole. #1083. $12.50/ea, 19 left. |
 |
SPRING LINER - Tough, slippery UHMW plastic. 20' roll, 2-1/4" wide x .025" thick. #UHMW. $5/ea, 7 left. |
Mustang II Kits - These are pre-cut and welded Mustang II kits all ready to be welded in to your frame. Kits include crossmember, upper towers, and boxing plates if required. Will accept all aftermarket control arms and manual or power Mustang II racks. Here's what we have left:
1933-34 Ford car. #6634, $100, 1 left.
1934-35 Chev car. #23400, $300, 3 left.
Custom fit crossmember & towers with 60" track width. #14540, $320, 1 left.
1947-54 Chev P/U. #6354, $100, 1 left.
1955-59 Chev P/U. #6359, $100, 1 left. |
Customer Pictures
Lloyd from Cambridge is installing a Welder Series Mustang II kit in this Oldsmobile. |
|
| And remember...
|
|
| |
|
copyright © www.welderseries.com |
