discount

Views:

Pages:

- Exhaust Grommet
  
  from $1.50
  
  Grommet made from high-temp urethane for insulating the exhaust pipes from the frame. Use with Welder Series' exhaust hangers. Now available: Super hi-temp blue grommets.
- Exhaust Hangers
  
  from $5.00
  
  Brackets for mounting your exhaust, in one and two hole configurations, made from mild steel and stainless.
- Gusset with 3 holes, 90 degree
  
  from $4.00
  
  10 ga. steel, available 3"x3" and 5"x5".
- Reinforcing Plate (fishplate)
  
  from $2.75
  
  2-1/2" x 5", used to reinforce a butt-welded joint. 10 ga mild steel. Available with or without a hole in the middle.
- Urethane Bushing Outer Sleeve
  
  from $3.15
  
  This is the tube that the urethane bushing kits fit into. Available for both large and standard bushings.
- Frame Bracket - "VersaTab"
  
  from $3.00
  
  Use this plate as a motor mount frame plate, a hiboy shock mount, a bracket off of a round tube, or in lots of other places. This is a very versatile plate.
- Axle Tab, Upper
  
  $3.25
  
  Upper axle tab for triangulated four link kits.
- Brake Tab
  
  $2.00
  
  For mounting flexible brake lines to the frame.
- Threaded Tube, ¾" OD x ½" Long, 3/8-16
  
  $4.25
  
  Chamfered both ends so that this spacer can be used as a threaded insert, welded into a hole. Great for body mounts, etc. Sold each.
- Frame Bracket, 3-1/2" x 3-1/4"
  
  from $4.30
  
  3-1/2" x 3-1/4" with one 1/2" dia hole, 2-5/8" from opposite edge. Buy 10, get 10% off.
- Frame Tab, #18201
  
  $2.85
  
  The center of the 1/2" hole is 1-1/8" from the opposite edge. 10 ga steel. #18201
- Axle Tab #227031
  
  $3.00
  
  1-1/4" high x 1-1/2" wide with a 3/8" hole. This tab fits a 3" rear axle tube.
- Gusset, 1-1/2" x 2"
  
  $3.50
- Threaded Tube, ¾" OD x ½" Long, 5/16-18
  
  $4.25
  
  Chamfered both ends so that this spacer can be used as a threaded insert, welded into a hole. Great for bolt-on shock mounts, headlight mounts, running board brackets, etc. #21810
- Threaded Tube, ¾" OD x ½" Long, 7/16-20
  
  $4.25
  
  Buy 10, get 10% off.
- Gusset, 2-3/4" x 3"
  
  $4.90
  
  Lots of applications but often used to gusset the rear crossmember in a Model A with a raised & narrowed rear frame section.
- Body Mount, Model A #28206
  
  $5.50
  
  A clean, simple Model A front body mount.
- Spacer, 1" OD x 5/8" ID x 0.348" Thick
  
  $2.30
  
  Designed as the spacer used on the Chrysler K772 lower ball joint, under the nut, on a Mustang II spindle.
- Formed Mount, #00061
  
  $5.00
  
  This bracket has many uses. 3/8" hole is 7/8" from the edge. Overall dimensions are about 4" x 1-1/4".
- Ball Joint Housing
  
  $12.50
  
  For Chrysler screw-in ball joint K772, commonly used in aftermarket Mustang II tubular control arms.
- Threaded Tube, 1" OD x ¾" Long, ½-20
  
  $4.25
  
  Buy 10, get 10% off.
- Shock Mount Plate
  
  $6.80
  
  8-1/8" x 3" with 1 hole, 1/2" dia.
- Threaded Tube, 1" OD x 1-½" Long, 5/8-18 RH & LH
  
  from $5.00
  
  Buy 10, get 10% off! Also available in LH threads.
- Frame Tab, #18200
  
  $2.75
  
  The center of the 1/2" hole is 7/8" from the opposite edge. 10 ga steel. #18200. Halfer sale runs until Nov 30/12.
- Shock Cone
  
  $19.75
  
  3-1/4" dia. x 2" high, with a 7/8" hole. For Mustang II upper towers.