Catalog Products
- Views:
-
Plate; 23" x 7-1/2" x 3/16"
$25.00
Probably just what you think about when you think about a 23" x 7-1/2" plate. #14399
-
.jpg?96,96,0,100,80,1661119227)
Rear Shock Mount, Lower
$20.00
Designed as a lower shock mount for the rear end. Heavy-duty 3/16" formed steel for greater strength.
-
Through-Frame Hairpin Mount Kit
$58.00
From the outside of the frame rail, the look is traditional, but without the bracket below the frame. On the inside, only a button head shows.
-
-
-
Brake Pedal Bushing Half - Delrin
$5.00
Delrin bushing, used in all our brake/ clutch pedal bracket kits.
-
-
-
Steering Shaft Bearing Support
$15.00
1" seamless tubing, one end threaded 3/4-16 to take a rod end. Cut the tube to length and weld it in a convenient spot.
-
.jpg?96,96,0,100,80,1168803950)
-
Crossmember Plate - Mustang II Rear/Top
from $46.00
This is the plate that gets folded into the rear and top of our Mustang II crossmember, including the rack mounts.
-
-
Rod Ends, 3/8-24, RH & LH
from $13.00
3/8-24 thread, available LH and RH and with or without Teflon lining.
-
Crossmember Plate - Mustang II Front/Bottom
from $40.00
This is the plate that gets folded into the front and bottom of our Mustang II crossmember.
-
Lower A-Arm Mounting Kit
$47.00
Got some swap meet Mustang II tubular lower arms that didn't come with the spacers and gussets? Here are the pieces you need.
-
-
Strut Rod Bracket & Gusset Kit
$24.00
Use this kit as the frame mounts for stock-style Mustang II strut rods.
-
Flat Front Crossmember
from $50.50
For early Ford transverse leaf springs. This crossmember helps get the frame lower by about 1-1/2 - 2'' compared to a stock Model 'A' crossmember.
-
Ford Motor Mounts - Rubber Insulated
from $47.00
Universal frame mounts to put your SBF into almost every frame from T-Buckets to F100's.
-
-
Radiator Mount
$7.00
Formed, 1-3/4" x 1-1/2" with a 1" gusset and a 3/8" hole. Designed as a radiator mount but can be used to mount other things. Available for Driver and Passenger sides.
-
Coupler, Splined 3/4-36 #C736x2A
$19.00
Coupler, 1-1/4" OD x 1" long, splined ¾-36 with a set screw and lock nut. Used with the arm in our rear sway bar kit.
-
Sway Bar (anti-roll bar), bar only
from $55.00
36" or 44-46" long, ¾" dia, 4142 cold finish, heat treated. One end splined ¾-36. The other end can be cut off to the length you need.
-
-
Frame Bracket, #21194
$8.00
Use on frames made from rectangular tubing with no taper when viewed from the side.
-
-
Four Link Kit; Rear, 8.8 Ford or GM
from $340.00
If you plan to use a Ford 8.8 or GM rear end, we have a kit with brackets to fit on the factory upper rear end bushings.
-
-
Frame Tab
$3.75
For 1-1/2" - 1-3/4" diameter tubing. Tab has a 3/8" hole 5/8" off the edge of the tube.
-
Tube, 1" OD x 5/8" ID x 3-3/8" Long
$10.00
Used in our lower control arm mounting kit and rear coilover mounts.
-
-
-
Coil-Over Mount, Upper
from $51.20
Upper coil-over mounts, typically used on Model A rear crossmembers.
-
Comments