Plates

Views:

Pages:

- Clamp Plate Spacer #15703
  
  $5.78
  
  3-1/2" x 1-3/4" x 1/4" thick. Hole is 9/16".
- Coil Over Mounting Plate #21902
  
  $10.50
  
  The 1/2'' hole is 8'' from the bottom of the plate and 4'' from the vertical edge. As used in the Welder Series' coil-over style Mustang II kit.
- Differential Plate, 8" Ford, 20668D
  
  $6.25
  
  Used in our bolt-on rear 8" Ford Panhard kit.
- Differential Plate, 9" Ford, 26901
  
  $7.25
  
  Used in our bolt-on 9" Ford rear Panhard kits.
- Driveshaft Loop Plate
  
  $29.00
  
  4-1/2" x 10" ID, 12 holes, 3/8" diameter.
- $2-1/2\" 3 bolt exhaust flange$
  
  Exhaust Flanges
  
  from $8.75
  
  For 2-1/4" and 2-1/2" tubing, in stainless and mild steel. Matches the standard Mr. Gasket #5980 gasket (not included).
- Frame Bracket #12501
  
  $5.78
  
  Plate, 4-3/4" x 4" with 1 hole, 1/2" dia, 4" from the opposite edge.
- Frame Bracket #18502
  
  $7.00
  
  7-1/4" x 4-3/4" (approx) x 3/16" thick with 2 holes 5/8" diameter on 5-1/2" centers.
- Frame Bracket - "VersaTab"
  
  from $4.60
  
  Use this plate as a motor mount frame plate, a hiboy shock mount, a bracket off of a round tube, or in lots of other places. This is a very versatile plate.
- Frame Bracket Side Plate, #20102
  
  $6.50
  
  6-1/8" x 4-1/4" with 2 holes, 1/2" dia, on 4-3/4" centers.
- Frame Bracket, #21194
  
  $8.00
  
  Use on frames made from rectangular tubing with no taper when viewed from the side.
- Frame Bracket, 3-1/2" x 3-1/4"
  
  from $4.30
  
  3-1/2" x 3-1/4" with one 1/2" dia hole, 2-5/8" from opposite edge. Buy 10, get 10% off.
- Frame Plate, #20294
  
  $4.00
  
  2-1/2" x 1-5/8" with a 1" diameter hole, used in our rear coil over bracket kits.
- Gusset, 3-7/8" x 3-7/8"
  
  $8.00
  
  As supplied in our Chrysler motor mount kit.
- Hood Latch Bracket, Model A
  
  $5.90
  
  This bracket welds to the frame instead of drilling & tapping the thin (1/8") wall tubing usually used.
- Pinion Plate, 8" Ford, 20668P
  
  $7.50
  
  Used in our 8" Ford bolt-on rear Panhard kits.
- Pinion Plate, 9" Ford, 26902
  
  $9.00
  
  Used in our bolt-on 9" rear Panhard kit.
- Plate, for Bolt-On Shock Mount
  
  $7.25
  
  3-½" x 2-3/8" with 4 holes 5/16" diameter. Designed to turn #1030 into a bolt-on mount. #10305
- Plate; 23" x 7-1/2" x 3/16"
  
  $25.00
  
  Probably just what you think about when you think about a 23" x 7-1/2" plate. #14399
- Rack Mount- Mustang II
  
  from $8.00
  
  Supplied flat, this 10 ga. Mustang II rack mount is available with a slot or a hole.
- Rear Plate for #27801 Axle Bracket
  
  $7.25
  
  This plate welds between two of #27801 axle bracket plates.
- Reinforcing Plate
  
  $8.00
  
  Used with the frame brackets in Model A rear four link kits. Laser cut 1/4" steel with two 5/8" holes on 5-1/2" centers.
- Reinforcing Plate (fishplate)
  
  from $2.75
  
  2-1/2" x 5", used to reinforce a butt-welded joint.
- Shock Mount Frame Plate
  
  $5.00
  
  The center of the notch would be 3" above the frame and 2-3/4" out from the frame. Usually used in pairs with a 3/4" diameter tube (see #10304) welded in the notch.
- Shock Mount Plate
  
  $6.80
  
  8-1/8" x 3" with 1 hole, 1/2" dia.