Mustang II Parts

Mustang II Parts

Views:

- C Notch Fill Piece - Front #12202
  
  $11.90
  
  Used as a filler for the front c-notch for Mustang II rack bellows clearance.
- Ball Joint Housing
  
  $12.50
  
  For Chrysler screw-in ball joint K772, commonly used in aftermarket Mustang II tubular control arms.
- Rack Mount Spacer Kit
  
  $23.00
  
  Rack mount spacers must be used with 1979 and newer power racks to move the rack centerline to the same position as the stock 1974-78 rack.
- Shock Cone
  
  $19.75
  
  3-1/4" dia. x 2" high, with a 7/8" hole. For Mustang II upper towers.
- Tower Top Plate
  
  $11.00
  
  For Mustang II, 6-5/8" along straight edge x 5-¾". The slots are 9/16" x 1-¾". The hole is 3-¼" dia.
- Upper Tower Plate, for Coil Spring Mustang II
  
  $29.00
  
  Wrap-around, for Mustang II, formed to be used with the top tower plate #14321 and shock cone #1083A.
- Coil Over Mounting Plate #21902
  
  $10.50
  
  The 1/2'' hole is 8'' from the bottom of the plate and 4'' from the vertical edge. As used in the Welder Series' coil-over style Mustang II kit.
- Crossmember Plate - Mustang II Rear/Top
  
  from $46.00
  
  This is the plate that gets folded into the rear and top of our Mustang II crossmember, including the rack mounts.
- Crossmember Plate - Mustang II Front/Bottom
  
  from $40.00
  
  This is the plate that gets folded into the front and bottom of our Mustang II crossmember.
- Strut Rod Bracket & Gusset Kit
  
  $24.00
  
  Use this kit as the frame mounts for stock-style Mustang II strut rods.
- Formed Notch Plate
  
  $8.00
  
  7-1/2" tall x 6-3/8" wide x 1-3/4" high. #674213
- Strut Rod Bracket
  
  $8.00
  
  Has also been used as a Flathead motor plate. Laser cut from 3/8" steel.
- Upper Arm Plate, for Coil-Over Mustang II
  
  $28.00
  
  This is used in the Welder Series coil-over style Mustang II kit. Use with #21902.
- Mustang II Brake Kit - For Granada Rotors
  
  from $68.86
  
  Adapts 1975-80 Granada rotors to Mustang II spindles.
- Spacer, 1-½" OD x 5/8" ID x ¾" Long
  
  $7.05
  
  Used as a spacer for later Mustang II power racks to correct the rack centerline and provide input shaft casting clearance. The rack will require one spacer for each side.
- Mustang II Brake Kit - For Camaro Rotors
  
  from $90.00
  
  Adapts 1982-92 Camaro rotors to Mustang II spindles.
- Spindle Nut Kit, Mustang II
  
  $27.40
  
  When Camaro rotors are used on Mustang II spindles, this nut kit lets you put a cotter pin through the stock spindle hole.
- Sway Bar Mount
  
  $13.25
  
  Formed and notched to weld to tubular lower arms when you want to use a Chassis Engineering (the street rod parts company) Mustang II style sway bar.
- Strut Rod Washer
  
  $0.50
  
  2-¼" OD x 1-½" ID x 1/8" thick.