Front Suspension Parts

Views:

Pages:

- Urethane Bushing Kits
  
  from $9.30
  
  Includes two bushing halves and one inner sleeve.
- Urethane Bushing Outer Sleeve
  
  from $3.15
  
  This is the tube that the urethane bushing kits fit into. Available for both large and standard bushings.
- Adjuster Kits
  
  from $15.40
  
  Threaded adjusters available tig welded or ready-to-weld.
- Frame Bracket, Formed
  
  from $14.00
  
  10 ga. steel. Hole is 1/2" dia, 2-5/8" from the opposite edge. Base is 3-1/2".
- Rack Mount- Mustang II
  
  from $8.00
  
  Supplied flat, this 10 ga. Mustang II rack mount is available with a slot or a hole.
- Adjuster Studs
  
  from $8.50
  
  Adjuster studs available in 3/4-16 and 5/8-18 threads, and for large or standard bushings. Great for custom bars!
- Batwing Boss, #10036
  
  $4.00
  
  Batwing boss, designed for front 4-link and hairpin batwing brackets.
- Through-Frame Hairpin Mount Kit
  
  $58.00
  
  From the outside of the frame rail, the look is traditional, but without the bracket below the frame. On the inside, only a button head shows.
- Lower A-Arm Mounting Kit
  
  $47.00
  
  Got some swap meet Mustang II tubular lower arms that didn't come with the spacers and gussets? Here are the pieces you need.
- Frame Bracket #12501
  
  $5.78
  
  Plate, 4-3/4" x 4" with 1 hole, 1/2" dia, 4" from the opposite edge.
- Frame Bracket Side Plate, #20102
  
  $6.50
  
  6-1/8" x 4-1/4" with 2 holes, 1/2" dia, on 4-3/4" centers.
- Clamp Bar for Spring Perch Kit
  
  from $6.00
  
  For 1-3/4" or 2" leaf springs, with 3/8" holes.
- Bars - 7/8" OD
  
  from $31.00
  
  7/8" bars, threaded 5/8-18 one end and notched for a 1-3/8" urethane bushing eye.
- C Notch Fill Piece - Front #15001
  
  $7.50
  
  Used to fill in the front leaf spring c-notch.
- Batwing C Plate - For Hairpins
  
  $8.50
  
  Formed c plates for hairpin radius rods, to be used with #10036 perch pin bosses.
- Batwing Side Plate - For Front Four Link, #14106
  
  $5.75
  
  Plate, front 4-link axle bracket side. 2 holes, 1/2" dia on 4-3/4" centers.
- Clamp Plate Spacer #15703
  
  $5.78
  
  3-1/2" x 1-3/4" x 1/4" thick. Hole is 9/16".
- Shock Mount Frame Plate
  
  $5.00
  
  The center of the notch would be 3" above the frame and 2-3/4" out from the frame. Usually used in pairs with a 3/4" diameter tube (see #10304) welded in the notch.
- Tie Rod
  
  $45.00
  
  Connects the spindle steering arms on early Ford front suspensions.
- Batwing Side Plate - For Hairpins, #28905
  
  $9.75
  
  For hairpin radius rods. 3/8" thick with 2 holes, 3/8" dia. on 4-3/4" centers.
- Clamp Plate Crossmember Tab #15715
  
  $3.25
  
  Used in our #15710 U-Bolt Eliminator kit, welded to the crossmember. 3-1/2" x 1" with a 3/8" hole.
- Drag Link Tube
  
  $38.00
  
  Connects the Pitman arm to the steering arm, for 1928-40 Fords with a solid axle. Threaded 11/16-18 LH/RH.
- U Bolt, ½-20 thread
  
  $2.35
  
  2-½" ID, 3-½" legs. Use with #15702 clamp plate. Does not fit stock Ford clamp plates.
- Clamp Plate Base, Front #15702
  
  $14.70
  
  4 holes are 1/2", center hole is 9/16". This clamp plate will not fit original u-bolts.
- Clamp Plate Base, Front #15712
  
  $9.50
  
  Clamp plate base for u-bolt eliminator kit WS15710. Center hole is 9/16''. The 2 outer holes are 3/8''. 3/8'' steel. 3-1/2" x 4-3/8".