Chassis Parts

Views:

Pages:

- Bars, 1" OD
  
  from $33.00
  
  1" OD bars with either 5/8-18 or 3/4-16 threads, available for large or regular bushing sizes.
- Axle Bracket Kit, for Coil-Overs
  
  from $64.00
  
  Heavy-duty 3/16" formed steel, available with or without a coil-over bolt kit.
- Axle Tab #227031
  
  from $0.00
  
  1-1/4" high x 1-1/2" wide with a 3/8" hole. This tab fits a 3" rear axle tube.
- Batwing Boss, #10036
  
  $4.00
  
  Batwing boss, designed for front 4-link and hairpin batwing brackets.
- Body Mount - Model A Rear #00206
  
  $6.00
  
  For model A frames that have a kicked and narrowed rear frame section.
- Body Mount, Model A #28206
  
  $5.50
  
  A clean, simple Model A front body mount.
- Brake Tab
  
  $2.00
  
  For mounting flexible brake lines to the frame.
- C Notch Fill Piece - Front #15001
  
  $7.50
  
  Used to fill in the front leaf spring c-notch.
- C Notch Fill Piece - Rear #12203
  
  $12.75
  
  Used to close in the c-notch in the rear of frame rails.
- Coil-Over Mount, Upper
  
  from $51.20
  
  Upper coil-over mounts, typically used on Model A rear crossmembers.
- Driveshaft Loop Kit
  
  from $138.00
  
  A unique driveshaft loop to tie in to your center section.
- Driveshaft Loop Plate
  
  $29.00
  
  4-1/2" x 10" ID, 12 holes, 3/8" diameter.
- Frame Bracket #18502
  
  $7.00
  
  7-1/4" x 4-3/4" (approx) x 3/16" thick with 2 holes 5/8" diameter on 5-1/2" centers.
- Frame Bracket - "VersaTab"
  
  from $4.60
  
  Use this plate as a motor mount frame plate, a hiboy shock mount, a bracket off of a round tube, or in lots of other places. This is a very versatile plate.
- Frame Bracket Side Plate, #20102
  
  $6.50
  
  6-1/8" x 4-1/4" with 2 holes, 1/2" dia, on 4-3/4" centers.
- Frame Bracket, #21194
  
  $8.00
  
  Use on frames made from rectangular tubing with no taper when viewed from the side.
- Frame Bracket, Formed
  
  from $14.00
  
  10 ga. steel. Hole is 1/2" dia, 2-5/8" from the opposite edge. Base is 3-1/2".
- Frame Curves
  
  from $39.00
  
  A unique and inexpensive alternative to thin-wall mandrel bent frame sections. Available for 2x3, 2x4, 2x5, and 3x3 tubing.
- Frame Tab
  
  from $0.00
  
  Used in front Panhard kits and many other applications. #21942S
- Gusset, 1-1/2" x 2"
  
  $3.50
- Gusset, 3" x 2-1/4"
  
  $3.60
- Gusset, 6" x 3"
  
  $8.50
  
  The relief along the straight sides minimizes weld distortion and the corner angle cut gives extra clearance.
- Hood Latch Bracket, Model A
  
  $5.90
  
  This bracket welds to the frame instead of drilling & tapping the thin (1/8") wall tubing usually used.
- Radiator Mount
  
  $7.00
  
  Formed, 1-3/4" x 1-1/2" with a 1" gusset and a 3/8" hole. Designed as a radiator mount but can be used to mount other things. Available for Driver and Passenger sides.
- Rear Crossmember - Model A
  
  from $69.00
  
  Designed to wrap around the back of the differential instead of over the top.